Oh Mann... Danke dir!
What doesn't kill you, gives you XP.
Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Zombie ()
|braunes Base||ST 4|
|grünes Base||ST 3 + Jump Up|
I thought I'd take a moment to outline plastics in a bit more detail as well, as we often see people on here getting very confused and a single accurate point of reference would probably be quite useful. I've spoken to a lot of people in the industry and any numbers I quote are generalisations, not the prices for any specific manufacturers, including Wargames Factory.
The headline figure that most people talk about is how GW sell a $40 boxed set which has about 50c worth of plastic in it, so I thought it would be helpful to break that cost down a bit. An average plastic tool for a single wargaming infantry sprue runs $8,000-$17,500 (depending on detail, bits, etc). Sculpting for plastic on top of that is expensive due to the highly qualified people needed, often salaried, but more often outsourced for thousands of dollars per model. Manufacturing requires either heavy equipment and all the costs that go with it, or you have to outsource it to someone who takes their cut. As such, price per sprue can be anything from $0.80 - $3.50. Add on shipping, marketing, warehousing, distribution and retail costs, etc and that $40 gets cut down very quickly, even if the raw material price is pennies per sprue. Typically 5000+ copies of a sprue have to be sold just to break even. Beyond that things become quite profitable quite quickly, but it is a massive gamble for non-GW wargaming companies (like mantic and hawk wargames) to take so we should certainly support those who take the risks and be thankful to kickstarter for enabling so many companies to take a chance where before they would have only been able to dream about it.
People also quibble a lot about materials these days as there are so many options out there, so here are the main ones:
Plastic - Polysterene is the stuff that Games Workshop use on their sprues, specifically HIPS. This is the only type of plastic that can be glued by plastic glue (polysterene cement).
Plastic - Restic/PVC - This is the stuff that CMON, PP, Mantic, Fantasy Flight (X-Wing) and many others are using as a plastic on a lot of their stuff. Technically it is plastic, but it is not the same that we are used to with sprues. The detail tends to be a bit softer as the material shrinks a lot when it sets, warping sharp edges on things like weapons and bending staffs and swords if it dries at an uneven pace. Cleaning up mould lines can be tough. There are chemicals that will clean mould lines but they give off poison fumes so are not readily recommended by companies that use it.
Plastic - ABS - This is what Lego use for their plastic. I've not seen it used on any wargaming models that I can think of, but some model tanks and similar use it.
Resin - There are a huge variety of resins and even more ways to create things with them. They are usually more brittle than other materials, require competent casters to prevent bubbles and issues, and have a very high per-model cost with moulds decaying over as few as 100 models or so, leading to high moulding costs. Most resins shrink a little when setting as well, but by much less than PVC. A single resin model can cost as much as $7-8 to produce.
Metal - There are lots of metals in use as well, typically tin or pewter alloys, with lead being used back in the day and by some small producers still. Metal can be tough to clean but is easier than resin to work with. The raw material cost can be higher than most resin so it has been phased out by most producers. Metal shrinks a bit when setting as well. Final detail is typically less than resin due to shrinkage but better than PVC.
Die finde ich auch super, außer dass ich nie unterscheiden konnte, wer die Ulfs und wer die Berserker waren.
The raw material cost can be higher than most resin so it has been phased out by most producers.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Prince ()